Are you attending the Pipe and Tube Show in Nashville this June? If you are, come listen to our talk on “Evaluating Product Integrity with Eddy Current.”
While fasteners may not be expensive end items, failure in critical applications can cause catastrophic effects. Criterion NDT provides in-line heat treat and crack non-destructive testing systems to verify the integrity of all part coming off an assembly line.
For full details of the article, look on page 80 in Fastener Technology at: http://www.bluetoad.com/publication/?m=5831&l=1
In its 2000 annual survey, Quality Magazine found that only 43.9% of manufacturers were performing “in-process” inspection of parts. Today, the same survey indicates 95% are doing so. Criterion NDT’s eddy current testing systems are designed to seamlessly integrate into modern manufacturing processes and support in-process inspection.
See the full article in the NDT Update eNewsletter at: http://www.ndtmag.com/Articles/Feature_Article/BNP_GUID_9-5-2006_A_10000000000001152980
Ford Motor Company announced this week that it is recalling over 200,000 Freestar and Mercury Monterey minivans made during the 2004 and 2005 model years, because their torque converter output shafts may fail. A number of the failures were found to be attributed to the torque converter output shaft splines stripping, causing a sudden loss of power to the drivetrain. As of this writing, the actual reason for this spline failure is not known. However, it is not outside the realm of possibility that this failure may ultimately be attributed to an improper heat treatment of the output shaft splines, which was not identified during the manufacturing process.
Eddy current test systems are one of the best ways to monitor the quality of heat treatment processes at production line speeds. A properly configured eddy current system can automatically sort out suspect bad product and alert production personnel to a potential upstream process failure. Early identification by eddy current testing can help to minimize quarantined product, reduce scrap and save money. Most importantly, the use of eddy current testing for material heat treatment (material structure) verification ultimately reduces the odds of experiencing the embarrassment of shipping product that does not meet a customers quality standards, or worse, fail during its intended use.
During the past couple of years we have all witnessed many changes. Factories have closed and people have either lost jobs or been shuffled around within their existing organizations. Those who were fortunate enough to retain employment may have found themselves in new positions and may also have aquired added responsibily for departments, personnel and equipment. Criterion NDT is here to help support those companies and the individuals who use the Zetec or Uson Eddy Current “Component Testing” Instrumentation. If you need assistance with your component testing application, or just have an interest in a quick “refresher” on the operation of the test instrumentation, please give us a call at 1-253-929-8800.
Article titled “Eddy Current Validates Critical Heat Treat Processes” published in the June 2011 issued of Quality Magazine. The article covers the utilization and benefits of eddy current testing for automated in-line evaluation of heat treated products. http://digital.bnpmedia.com/publication/?i=71537&p=70
Criterion NDT will present a paper on Advancements in Eddy Current Heat Treat Testing at the 2011 Quality Conference. The Conference takes place from April 11th – 13th in Charlotte, NC. For more information on the the Conference, visit http://www.qualitymagconference.com.
GM expanded an earlier recall of some 2011 model-year trucks and SUV’s due to a heat treatment process failure of a rear axle cross pin.
This is another prime example of why proper heat treatment process verification/material structure testing of critical components with eddy current is so important.
It’s likely that a rear axle cross pin is a relatively inexpensive part to produce, but the cost of failure can be many times greater. Properly installed and operated eddy current test systems can help to reduce and/or eliminate the risk of experiencing this type of product failure.
Don’t wait until it’s too late to add eddy current testing to your manufacturing quality process. Like insurance, you’ll be very glad you had it when you needed it.
Criterion NDT is growing! We are looking for new Independent Sales Representatives to join our existing network. Are you interested?
Independent Sales Representative should haves:
- A working relationship with manufacturers of automotive and medical component OEMs in their desired territory.
- A knowledge of automotive manufacturing processes for metallic components such as bearings, pistons, and axles.
- A knowledge of medical manufacturing processes for metallic components such as hypodermic needles.
- A basic knowledge of electrical principles and electronic instrumentation.
Independent Sales Representative nice to haves:
- A knowledge of non-destructive testing processes. Knowledge of eddy current testing is a definite plus.
- A knowledge of metallurgy; specifically heat treat processes.
- Experience developing material handling systems or working with third party material handling companies.
Independent Sales Representative must haves:
- 5+ years experience selling complex systems in a B2B environment.
- A positive can-do attitude.
If you are interested in learning more, please call us at 253-929-8800 or reply to this post.
Eddy current technology can be utilized for verification of proper induction hardening processing. Examples of some rejectable material structure conditions that can result from an improper induction hardening process (or interrupted process), which can be detected with eddy current technology are :
- Short heat
- Short quench
- Delayed quench
- Air cooled (no quench)
- Misplaced Case pattern (due to bent induction coils)
- Shallow Case depth
These rejectable “material structure” conditions can be detected on line without process flow interruption and tests EVERY part. This results in less scrapped material and potentially a huge annual cost savings if your producing a high dollar product.